What started life as an original 1979 930 3.0SC has changed a lot under the somewhat new Porsche shop called Theon Design. This particular 911 combines the classic bodywork of the original car with a bespoke interior and drive-train combination. Well, for starters, apart from the hand stitched leather interior, bespoke body modifications, custom 17-inch Fuchs wheels, custom coil-overs and other mods, the vehicle features a Porsche motorsport RS engine. The powerplant, originally destined to race in the 993 SuperCup Series, was supplied by Porsche Motorsport and it was built to RS specifications. That includes equal length stainless steel manifolds (among other stuff), and a power output of 300 HP.

I generally like modern cars versus older cars. The speed of innovation and technology development is so fast that it is hard for me to get excited about a 30 year old supercar that can be beaten by a Toyota Camry in any performance test. I would rather dream about the the new McLaren Speedtail. However, about six months ago I bought my first Porsche and all of a sudden things started to change. I found myself talking to guys at local Porsche shows who had build or bought restomodded 911s and 356s and couldn’t help but lust for one myself.

This is the most worthless thing I every purchased. I did not get enough pressure to wash a dish. Then Prime Time solutions did not send the battery and charger with the gun. After waiting on two deliveries.The item proved Wothless. Now I face the ordeal of getting my money Back.

Wanna create comparison chart graphs just like I do for GPS, heart rate, power meters and more? No problem, here’s the platform I use – you can too!

As you might imagine, table saw power increases from benchtop through cabinet models. Looking specifically at jobsite table saws narrows things down considerably. Buying a table saw for jobsite use, you’ll want a 15-amp motor. There’s plenty of ripping power and you only need 120V AC power.

Gladiator advantagesWhile both vehicles are very capable off-road, if you’re one of those who take that activity seriously, the Gladiator will merrily keep on going after the ZR2 has had to surrender to its limits. This Jeep is really built to overcome the most difficult obstacles thanks to elements like a disconnectable front stabilizer bar.

Though Jacobs likes the single ring option, he also knows some riders like smaller steps between gears and don’t feel the need for a dropper, so he will offer a double ring setup. I don’t mind the single ring set up as it frees up the left shifter to actuate the dropper post.

This build started as a low-mileage, numbers matching 1973 911T and was fitted with steel RS flares (butt welded), steel RS Touring rear bumper, steel 911S front bumper and a fiberglass ducktail. The Brumos-style race livery really pops against the crispness of the Grand Prix White paint. The original 2.4L motor was rebuilt to 2.7L specifications including 90mm pistons, performance cams, ported/polished intake manifolds and Weber 40IDA carburetors with custom jetting. The factory 915 transmission was bolstered with a Quaife limited-slip differential, lightweight flywheel and factory short-shifter. The interior has been refreshed in a lightweight but not barebones fashion.

I’ve had over 20 years without crashing or being crashed into, as I drive defensively. I’ll take a modern Japanese car, over a Ford Imploder from 2004 any day.

When a train is too long to fit into a yard track, the train must be separated and put on two or more tracks, adding to yard congestion and additional delay.

I am looking to upgrade from my first table saw which is the Ryobi that you reviewed (had to find something cheap that was decent). I do a lot of rip cuts, as well as fine precision cuts for laminating and joinery required for frames, furniture, etc. I am looking at the Skilsaw and the Dewalt 7480 and cannot decide which would be best for me. Any insight would be helpful!

An internal review undertaken by Alcon identified that its brake disc manufacturing operation was a specific pinch point that was affecting the company’s overall productivity and operational efficiency.