Based on the same real-life “honor killing” that inspired fellow German Feo Aladag’s prize-winning 2010 feature “When We Leave,” Sherry Hormann’s “A Regular Woman” takes a compelling new approach to the contentious 2005 case that shocked Germany: By allowing the murdered woman — a 23-year-old German of Turkish-Kurdish ancestry shot point blank by her youngest [...]

Cutline Marker Accuracy: On at 90°. On at 45°Blade Visibility: Very Good – nice view windowBevel Angle Setting: Good – two scales; 1° increments; incised markings; no contrastGuard Action: Very Good on shave cuts – extra-large outboard lobe helpsTracking against Straightedge – GoodGrip and Trigger: Good – requires slight repositioning of hand for best cutting grip after reaching the push-in safety button

Dust collection is above average with the M18 Fuel table saw’s design. You’ll notice a soft canvas-like layer that moves along with the blade bevel and helps deliver more dust to the port. Even if you’re working outside where you can shoot it out, sawdust doesn’t collect below the blade as much as a couple of our other saws.

Buying a discounted chevy 1500 IS cheaper then buying a Colorado! With a crap tow compacty, ugly, and ugly. Buy a full size! My 2017 1500 best mpg was 26! And I can put 5 full size adults in it!

A: Yes, absolutely. Rigid insulation sheets are one of the best things you can do when renovating the outside of a building before new siding goes on. It boosts effective insulation action and makes stud wall cavities warmer for any given outdoor temperature. This last benefit is important. Warmer stud cavities greatly lessen the chances condensation will occur inside wall cavities during cold weather. Double-wall construction boosts the energy efficiency of a building too, but it’s much more difficult to install in a retrofit situation.

Elsie Van Niekerk (owner), Goodman Mthethwa (Guillotine operator) Richard Ngcobo (setter) from Durban Blacksmith and Ms Audrey Kaunda (mechanical technology educator) with the second group of Grade 12 learners from Inanda Newtown Comprehensive High School, proudly displaying their cut and bend parts for their practical task to make a safe.

Now, this isn’t terribly different from Shimano’s Syncro Shift.  It’s actually sort of a blend of Shimano’s two full and semi modes, since it can be configured to jump either one, or two gears as part of the shift. Whereas in Shimano’s case they offer two distinct modes for that piece. Frankly rather subtle differences.

To further understand how panel bending fits into a modern metal fabricating operation, let’s look at how two companies are using the technology to stay on top of increased production demands. Datum Storage Solutions Inc., Emigsville, Pa., and NSA Industries LLC, St. Johnsbury, Vt., adopted panel bending for different reasons, but they are finding that it’s delivered a similar result—additional bending capacity when they needed it most.

No key required. The Corsair has a phone-as-key feature that’s activated through the Lincoln Way app. The phone can also store your preferences and set them up as you get into the vehicle. And of course you can remote start the Corsair, among other features.

To evaluate the performance of the saws, I first fitted them all with identical 24-tooth Irwin Marathon WeldTec blades to make sure I was testing the saws without any influence of the stock blades. The Festool takes special blades, so I used it with their own 18-tooth blades throughout the testing.

Coolest detail: Aluminum lower rocker. Seven is synonymous with titanium, but for the purposes of this part, aluminum was the better choice, with the titanium chainstays bolting to it. (A preproduction rocker is shown; the production rocker will be smaller and more elegant). Seven’s director of marketing, John Lewis, provided multitudinous reasons for machining this part out of one piece of aluminum instead of making it from welded titanium. The aluminum part is lighter, more durable, less costly, and builders are better able to maintain the frame’s alignment. “If we built this in titanium it would have a lot of weldments, complications, and cost—while also being heavier. Also, by using aluminum and increasing the overall external shape and size, we also increase its stiffness,” he said.

Tesla pointed the blame at “incorrect settings on its printers” and “workers’ poor operation.” The company is now working with the Chinese government to look for solutions.